在高温凝胶渗透色谱法(GPC)测定聚烯烃时何时应用光散射检测器
在高温凝胶渗透色谱法(GPC)测定聚烯烃时何时应用光散射检测器

光散射检测器功能强大,但对于高温应用(例如 GPC/SEC)而言,其使用难度也相当高。它是唯一一种无需依赖色谱柱或校准即可提供绝对摩尔质量结果和长链支化计算的检测器。然而,其易损性和日常分析的高要求是在制定商业计划和确定最佳配置(兼顾所需性能、用途和成本)时需要考虑的重要缺点。
从这个意义上讲,兼具最佳平衡性和稳健性的最佳配置是双检测系统,它将浓度检测器(例如红外检测器 IR4 或 IR6,或差示折射率检测器)与粘度计检测器相结合。这种组合可以计算长链支化度,而无需使用光散射检测器,后者存在固有的不便。这是通过将待分析样品的 Mark-Houwink 图与基于通用校准测定的特性粘度和摩尔质量的线性参考样品的 Mark-Houwink 图进行比较来实现的。Polymer Char 的 One 软件支持在此配置下进行长链支化度分析,并可计算粘度收缩因子 g'、支化数和支化频率的分布及平均值。
双检测器配置因其在大多数样品中表现可靠,且在潜在技术问题、价格和实用性之间取得了良好的平衡,因此在高温凝胶渗透色谱(HT GPC)用户中应用最为广泛。因此,它通常优于三检测器配置,后者结构更为复杂、成本更高,难以用于常规分析。
那么什么情况下采用三重检测配置?
在评估是否在高温凝胶渗透色谱 (HT GPC) 配置中加入光散射检测器时,应同时全面考虑待表征样品的类型。
- 对于长链支化物含量极低的情况,双检测器配置可能存在局限性,建议采用三检测器配置。三重检测配置(浓度检测器、粘度计和光散射检测器)能够基于测得的特性粘度和绝对摩尔质量绘制Mark-Houwink图,并在使用多角度光散射(MALS)时绘制构象图。在这种情况下,Polymer Char公司的One软件将提供长链支化(LCB)计算,包括收缩因子g(回转半径)和g'(粘度)、支化数、支化频率分布和平均值,以及粘度比、摩尔质量比和gpcBR系数。
- 最后,光散射检测器在分析结果中发挥重要作用的另一个特殊情况是超高分子量聚乙烯(UHMWPE)样品。这些特殊样品对凝胶渗透色谱(GPC)技术的分离能力提出了挑战,而多角度光散射(MALS)检测器能够测量绝对摩尔质量,因此有助于克服在高摩尔质量范围(超出色谱柱分离范围)内进行相对色谱柱校准的困难。
When to use a Light Scattering in High Temperature GPC for Polyolefins
April, 16 2026
Category: Intrinsic Viscosity Analysis, GPC/SEC

A Light Scattering detector is as powerful as it is challenging to use for high-temperature applications, such as GPC/SEC. It is the only detector that can provide absolute molar mass results and Long Chain Branching calculations without depending on columns or calibrations. However, its fragility and difficulties for routine analysis are a significant drawback to consider when elaborating your business case and deciding the best configuration in terms of desired performance, usage, and cost during a purchase decision.
In that sense, the winner configuration with the best balance result and robustness is a dual detection system that combines a concentration detector (such as an Infrared Detector IR4 or IR6, or a differential Refractive Index Detector), with a Viscometer detector. This combination allows the calculation of the Long Chain Branching without the inherent inconveniences of using a Light Scattering Detector. This is possible by comparing the Mark-Houwink graphs of the sample to be analyzed against those of linear reference samples, based on measured intrinsic viscosity and molar mass determined by universal calibration. Polymer Char’s One Software allows the LCB analysis in this configuration with the viscosity contraction factor g’, branching number, and branching frequency distributions and averages.
The dual-detector configuration is the most widely used among HT GPC users due to its reliable performance in most of the samples, plus its strong balance between potential technical issues, price and practicality. As a result, it is often preferred over triple-detector configurations, which are significantly more complex, costly and difficult to afford for routine analysis.
When a Triple Detection Configuration is Recommended
When assessing the decision of including a light scattering detector in the HT GPC configuration, this should be considered alongside a thorough review of the types of samples to be characterized. For cases in which the Long Chain Branching content is extremely low, the dual detection configuration might show limitations, and a triple detection configuration is recommended instead.
A triple detection configuration (concentration detector, viscometer and light scattering detector) allows obtaining the Mark-Houwink plot based both on measured intrinsic viscosity and also on absolute molar mass, as well as the Conformation plot when a MALS is used. In this case, Polymer Char’s One Software will provide LCB calculations including both contraction factors g (radius of gyration) and g’ (viscosity), branching number, branching frequency distributions and averages as well as the viscosity ratio, molar mass ration and gpcBR coefficient.
Finally, another particular case in which a light scattering detector may play a significant role in the results, is concretely for UHMWPE samples. These specific samples will challenge the GPC technique separation power itself, and having a MALS detector will help overcome those difficulties with the relative column calibrations in the very high molar mass range (beyond the columns separation range) thanks to its capability of measuring the absolute molar mass.
相关推荐
后台报名或咨询