沿分子量分布追踪羰基降解——GPC-IR检测聚烯烃能力的再提升
应用简报
沿分子量分布追踪羰基降解——GPC-IR检测聚烯烃能力的再提升
2026年6月
作者:Felipe Cordero, Alberto Ortín (Polymer Char)


引言
聚烯烃降解已成为再生塑料、长期耐久性研究、经灭菌处理的医疗器械、电缆绝缘材料、土工膜及先进配方领域中的一个关键问题。氧化降解会产生含氧官能团(尤其是羰基),这些官能团被公认为聚合物老化与降解的主要标志之一。然而,常规的体测式傅里叶变换红外光谱(FTIR)仅能提供平均信息,无法确定这些降解产物在分子量分布中的具体位置。这一局限性显得愈发重要,因为降解过程可能涉及多种相互竞争的机制。
链断裂是最常见的降解途径之一。热降解、光氧化降解及辐射诱导降解会产生自由基,这些自由基最终形成含羰基的物质,如酮、醛、羧酸和酸酐。
随着氧化过程的进行,聚合物链断裂成较短的链段,导致:
- ·较低的分子量
- ·较宽的分子量分布
- ·较高的羰基浓度
在聚乙烯和聚丙烯降解的研究中,羰基生成与分子量降低之间的这种关系已被广泛报道(Gugumus 等、Rabello 等、Celina 等)。
在其他体系中,降解过程可能引发交联反应。自由基复合反应不会生成较短的链,而是形成高度互连的结构。
这些材料的溶解度会逐渐降低,并可能在 TCB 或 oDCB 等常规高温凝胶渗透色谱(HT-GPC)溶剂中变得部分或完全不溶。
降解材料的表征工具
因此,恰恰在最需要降解信息的时候,分子表征变得愈发困难。
已有多种方法被应用:
- · FTIR 羰基指数
- · DSC 氧化诱导时间
- · 力学测试
- · 体样光谱分析
这些技术极具价值且应用广泛(Rapp、Celina、Rabello 等人)。然而,它们仅能提供平均信息,无法确定降解产物在分子量分布中的具体分布情况。
因此,根本问题依然悬而未决:羰基位于何处?
高温凝胶渗透色谱(GPC)联用红外检测器作为一种极具前景的解决方案脱颖而出,因为它能同时获取分子量与化学组成信息。IR6检测器的引入实现了对约1740 cm⁻¹处羰基信号的检测,为EVA及其他含羰基聚合物的分析开辟了新的可能。
然而,许多降解后的聚烯烃会生成含羰基的其它物种,其最强吸收出现在较高的波数范围,通常在 1780 cm⁻¹ 至 1790 cm⁻¹ 之间。此外,溶剂透明度的局限性也进一步限制了常规配置的适用性。
用于聚烯烃降解研究的羰基检测新谱带
为应对这一挑战,Polymer Char 开发了一种中心波长位于 1780 cm⁻¹ 的新型 IR6 滤光片。
该新型过滤器可实现:
- · 改进对降解相关羰基物种的检测
- · 在 TCB 流动相中进行分析
- · 提高信噪比
- · 对分子量分布范围内的羰基分布进行定性追踪
该能力在降解化学与分子结构之间建立了直接联系,为降解研究提供了一种新的分析工具。
本项工作的目的是通过涉及降解聚烯烃、马来酸酐改性聚烯烃和EVA共聚物的若干典型应用,展示新型1780 cm⁻¹ IR6滤光片的分析能力。
Applications 应用
应用 1 —— 降解聚丙烯链断裂过程中的羰基追踪
聚丙烯的氧化降解通常涉及断链反应,在降低分子量的同时生成含氧官能团。因此,测定羰基浓度随分子量的变化关系,可为深入了解降解机理提供直接依据(Celina 等人)。在本例中,采用新型 1780 cm⁻¹ 滤光片观测发现,羰基主要集中在低分子量组分中,这一结果与链剪切主导的降解过程相吻合。

降解过程首次得以沿着分子量分布进行追踪。
应用 #2:降解的 PP/PE 样品
降解后的 PP/PE 样品可能含有降解过程中产生的不同 CO 基团(如羰基或羧基)。得益于能够使用两种不同的滤光片(1740 cm⁻¹ 或 1780 cm⁻¹),目前已能更好地应对这些基团的存在。

降解聚丙烯(PP)的示例,其在两个波段产生不同的峰(粉色显示的 1780 波段(TCB溶剂),绿色显示的 1740 波段(oDCB溶剂)。
应用 #3:PE/PP-MAH 样品分析:
现在,利用位于 1780 cm⁻¹ 波段的新滤光片,并以 TCB 为溶剂,即可对含有马来酸酐的 PE/PP 样品进行分析。此前,由于样品与 oDCB 溶剂发生相互作用,可能导致其在 GPC 色谱柱中产生不可逆的滞留,因此一直无法使用 oDCB 对此类样品进行分析。
如今,改用 TCB 作为溶剂,样品能够正常通过色谱柱,且这种新过滤器允许对羰基进行测定,从而为分子量分布(MMD)和短链支化数据提供了极具价值的补充。

在TCB中分析的3种不同PE/PP-MAH样品在1780 cm⁻¹谱带处的羰基浓度
应用 4:EVA 分析
利用最初配置于 1740 cm⁻¹ 波段的滤光片及 oDCB 溶剂,IR6 检测器已能实现对 EVA 样品的测定,并成功定量分析了整个分子量分布(MMD)范围内的醋酸乙烯酯含量。
近期,研究人员改用配置于 1780 cm⁻¹ 波段的滤光片及 TCB 溶剂对这些样品进行了重新测试;结果显示,与此前采用 1740 cm⁻¹ 波段滤光片和 oDCB 溶剂的方案相比,新方案在灵敏度和信噪比方面均表现更佳。

在相同色谱条件(流动相为 TCB)下,传统 1740 cm⁻¹ 红外滤光片与新型 1780 cm⁻¹ 红外滤光片的比较。
6. References
1. Gugumus et al, (1995)., Thermooxidative Degradation of Polyolefins in the Solid State: Part 1. Experimental Kinetics of Functional Group Formation. Polymer Degradation and Stability, 52: 131-144.
2. Rabello & White, (1997)., Crystallization and Melting Behaviour of Photodegraded Polypropylene– 1. Chemi-Crystallization. Polymer Degradation and Stability, Vol. 38 No.26, pp.6379-6387.
3. Celina et al, (2013), Review of Polymer Oxidation and Its Relationship with Materials Performance and Lifetime Prediction. Polymer Degradation and Stability, 1-11.
4. Geraldine Rapp et al (2019).. Influence of the physical state of a polymer blend on thermal ageing. Polymer Degradation and Stability, 163, pp.161-173. 〈10.1016/j.polymdegradstab.2019.03.006〉.
5. Scott 2002. Degradable Polymers: Principles and Applications (2nd Edition) DOI 10.1007/978-94-017-1217-
Application Note. Carbonyl Degradation Tracking Along the Molecular Weight Distribution: Enhanced Detection for Polyolefins
June 2026
By Felipe Cordero, Alberto Ortín. (Polymer Char)
Carbonyl Degradation Tracking Along the Molecular Weight Distribution: Enhanced Detection with GPC-IR
Introduction
Polyolefin degradation has become a critical issue in recycled plastics, long-term durability studies, sterilized medical devices, cable insulation, geomembranes and advanced formulations. Oxidative degradation generates oxygen-containing functionalities, particularly carbonyl groups, which are among the most widely accepted markers of polymer ageing and degradation. However, bulk FTIR only provides average information and cannot determine where these degradation products are located across the molecular weight distribution. This limitation becomes increasingly important because degradation may proceed through different competing mechanisms.
One of the most common degradation pathways is chain scission. Thermal, photo-oxidative and radiation-induced degradation generate radicals that eventually form carbonyl-containing species such as ketones, aldehydes, carboxylic acids and anhydrides.
As oxidation progresses, polymer chains break into shorter segments, leading to:
- lower molecular weight
- broader MWD
- increased carbonyl concentration
This relationship between carbonyl formation and molecular weight reduction has been widely reported in polyethylene and polypropylene degradation studies (Gugumus et al, Rabello et al., Celina et al).
In other systems, degradation can induce crosslinking reactions. Instead of producing shorter chains, radical recombination forms highly interconnected structures.
These materials progressively lose solubility and may become partially or completely insoluble in conventional HT-GPC solvents such as TCB or oDCB.
Characterization Tools for Degraded Materials
Consequently, molecular characterization becomes increasingly difficult precisely when degradation information is most needed.
Several approaches have been proposed:
- FTIR carbonyl index
- DSC oxidation induction time
- Mechanical testing
- Bulk spectroscopy
These techniques are extremely valuable and widely used (Rapp., Celina, Rabello at al). However, they only provide average information and cannot establish how degradation products are distributed throughout the molecular weight distribution.
Consequently, the fundamental question remains unanswered: Where are the carbonyl groups located?
High-temperature GPC coupled with infrared detection appeared as a promising solution because it combines molecular weight information with chemical composition. The introduction of IR6 enabled carbonyl detection around 1740 cm⁻¹ and opened new possibilities for EVA and other carbonyl-containing polymers.
Nevertheless, many degraded polyolefins generate carbonyl species whose strongest absorptions occur at higher wavenumbers, typically between 1780 cm⁻¹ and 1790 cm⁻¹. Moreover, solvent transparency limitations further restrict the applicability of conventional configurations.
New carbonyl detection band for degradation studies in polyolefins
To address this challenge, Polymer Char has developed a new IR6 filter centered at 1780 cm⁻¹.
The new filter enables:
- Improved detection of degradation-related carbonyl species
- Analysis in TCB mobile phase
- Enhanced signal-to-noise ratio
- Qualitative tracking of carbonyl distribution across the molecular weight distribution
This capability provides a direct link between degradation chemistry and molecular architecture, creating a new analytical tool for degradation studies.
The objective of this work is to demonstrate the analytical capabilities of the new 1780 cm⁻¹ IR6 filter through several representative applications involving degraded polyolefins, maleic-anhydride-modified polyolefins and EVA copolymers.
Applications
Application #1 – Carbonyl Tracking During Chain Scission in Degraded Polypropylene
Oxidative degradation of polypropylene frequently proceeds through chain scission reactions, generating oxygen-containing functionalities while simultaneously reducing molecular weight. The ability to measure carbonyl concentration as a function of molecular weight therefore provides direct insight into the degradation mechanism (Celina et al). In this example, the new 1780 cm⁻¹ filter reveals carbonyl groups concentrated in the lower molecular weight fractions, consistent with chain scission-driven degradation.

For the first time, degradation can be tracked along the molecular weight distribution
Application #2: Degraded PP/PE samples
Degraded PP/PE samples may contain different CO groups such as carbonyl or carboxyl groups caused during the degradation process. The presence of these kinds of groups can now be better addressed thanks to the possibility of using two different filters (1740 cm⁻¹or 1780 cm⁻¹).

Example of degraded PP that generate different peaks in both bands (band of 1780 and TCB in pink color, and band of 1740 and oDCB in green color).
Application #3: Analysis of PE/PP – MAH samples:
PE/PP samples containing maleic anhydride can now be analyzed using the new filter located at band of 1780 cm⁻¹ and in TCB as solvent. The analysis of this type of samples by oDCB had not been possible so far due to potential unrecoverable retention in the GPC columns due to the interaction with the oDCB.
Now, with the new filter, TCB was used instead as samples can travel through the columns normally and the new filter allows the measurement of the carbonyl groups, which are an invaluable complement to the MMD and short chain branching data.

Carbonyl groups concentration in band of 1780 for 3 different PE/PP – MAH samples analyzed in TCB
Application #4: Analysis of EVA
Measurement of EVA samples had been possible by the initial IR6 detector and its initial filter located in 1740 cm⁻¹ band and using oDCB. This capability had been a success allowing quantifying the amount of vinyl acetate accoss the MMD distribution. These samples have now been tested again using the new filter located in 1780 cm⁻¹ band and TCB as solvent, obtaining superior results both in sensitivity and also in S/N ratio compared to the initial studies with the filter located in 1740 cm⁻¹ band and oDCB as solvent.

Comparison of the conventional 1740 cm⁻¹ and the new 1780 cm⁻¹ IR filters under same chromatographic conditions (mobile phase TCB).
6. References
1. Gugumus et al, (1995)., Thermooxidative Degradation of Polyolefins in the Solid State: Part 1. Experimental Kinetics of Functional Group Formation. Polymer Degradation and Stability, 52: 131-144.
2. Rabello & White, (1997)., Crystallization and Melting Behaviour of Photodegraded Polypropylene– 1. Chemi-Crystallization. Polymer Degradation and Stability, Vol. 38 No.26, pp.6379-6387.
3. Celina et al, (2013), Review of Polymer Oxidation and Its Relationship with Materials Performance and Lifetime Prediction. Polymer Degradation and Stability, 1-11.
4. Geraldine Rapp et al (2019).. Influence of the physical state of a polymer blend on thermal ageing. Polymer Degradation and Stability, 163, pp.161-173. 〈10.1016/j.polymdegradstab.2019.03.006〉.
5. Scott 2002. Degradable Polymers: Principles and Applications (2nd Edition) DOI 10.1007/978-94-017-1217-
相关推荐
留言咨询